manualshive.com logo in svg

Yamaha V-Star 1300, Руководство пользователя

Поделиться
Скачать
Yamaha V-Star 1300 Скачать руководство пользователя страница 74

PERIODIC MAINTENANCE AND ADJUSTMENT

7-33

7

EAU42452

Replacing a rear turn signal 
light bulb 

1. Remove the turn signal lens by re-

moving the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws. 

NOTICE:

 Do not over-

tighten the screws, otherwise
the lens may break.

 [ECA10681]

EAU42484

Replacing the license plate 
light bulb 

1. Remove the license plate light cov-

er by removing the bolts.

2. Pull the license plate light unit up

as shown.

3. Remove the license plate light

socket (together with the bulb) by
turning it counterclockwise, and
then pulling it out.

4. Remove the burnt-out bulb by pull-

ing it out from the socket.

5. Insert a new bulb into the socket.

1. Screw

1. License plate light cover

2. Bolt

1. License plate light unit

1. License plate light bulb socket

1. License plate light bulb

U5S612E0.book  Page 33  Wednesday, April 9, 2008  5:56 PM

Содержание V-Star 1300





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды