manualshive.com logo in svg

Yamaha V-Star 1300, Руководство пользователя

Поделиться
Скачать
Yamaha V-Star 1300 Скачать руководство пользователя страница 68

PERIODIC MAINTENANCE AND ADJUSTMENT

7-27

7

NOTICE

ECA10590

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.

EAU23282

Checking the steering 

Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.

1. Place a stand under the engine to

raise the front wheel off the
ground. (See page 7-1 for more in-
formation.) 

WARNING! To avoid

injury, securely support the ve-
hicle so there is no danger of it
falling over.

 [EWA10751]

2. Hold the lower ends of the front

fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.

EAU23290

Checking the wheel bearings 

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

U5S612E0.book  Page 27  Wednesday, April 9, 2008  5:56 PM

Содержание V-Star 1300





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды