Yamaha V-Star 1300 Скачать руководство пользователя страница 26

Страница: 26 / 100

INSTRUMENT AND CONTROL FUNCTIONS

4-9

EAU12890

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13091

Fuel tank cap

To open the fuel tank cap

Open the fuel tank cap lock cover, in-
sert the key into the lock, and then turn
it 1/8 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.

To close the fuel tank cap

1. Push the fuel tank cap into position

with the key inserted in the lock.

2. Turn the key counterclockwise to

the original position, remove it, and
then close the lock cover.

1. Brake lever

1. Brake pedal

1. Fuel tank cap lock cover

2. Unlock.

U5S612E0.book Page 9 Wednesday, April 9, 2008 5:56 PM

Содержание V-Star 1300





































































































Результаты поиска

Содержание V-Star 1300

Отзывы:

Бренды по названию

Популярные бренды

Yamaha V-Star 1300, Руководство пользователя

Результаты поиска

Содержание V-Star 1300

Отзывы:

Бренды по названию

Популярные бренды