Yamaha TDM850 1999 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 43

background image

–9–

1

Battery negative lead

2

Battery positive lead

3

Starter motor lead

4

Fuel sender lead

5

Fuel tank drain hose

6

Fuel tank breather hose (for DEU)

7

Water hose

8

Spark plug lead

9

Clutch cable

10

Brake hose

11

Throttle cable

12

Right handlebar switch lead

13

Headlight lead

14

Meter light lead

15

Speed sensor lead

16

Carburetor heater hose

17

Vacuum hose (#1)

18

Vacuum hose (#2)

19

Coolant reservoir breather hose

20

Carburetor breather hose

21

Rear brake switch lead

22

CYCLELOCK lead

A Route the battery positive lead

and battery negative lead through
the clamp.

B Fasten the wireharness Coolant

breather hose and flasher relay
lead.

C Route the carburetor breather

hoses through the engine clamp.

D Fasten the carburetor air vent hose.
E Route the carburetor breather

hoses, vacuum hose (#1) down
ward and vacuum hose (#2) up-
ward through the guide.

F Route the vacuum hose (#1) inside,

vacuum hose (#2) outside through
the guide.

G Fasten the coolant reservoir hose.
H Fasten the wireharness right han-

dlebar switch lead meter lead and
headlight lead with a clamp.

I Route the relay lead through the

outside of wireharness.

CABLE ROUTING

SPEC

«
...
13
14
15
16
17
...
»

Содержание TDM850 1999












































Отзывы:

Нет отзывов

Похожие инструкции для TDM850 1999

Бренд: GBRacing Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: SCORPION Страницы: 12

Rebellion Electric Chopper 15130760

Бренд: Razor Страницы: 17

Dirt Runner 90cc

Бренд: Baja motorsports Страницы: 66

Бренд: R&G Страницы: 24

Бренд: SHOEI Страницы: 38

Бренд: Cellularline Страницы: 2

Бренд: Suzuki Страницы: 522

Бренд: Qingqi Страницы: 48

Бренд: Yadea Страницы: 100

Бренд: MRA Страницы: 6

Бренд: Custom Dynamics Страницы: 2

Бренд: Royal Enfield Страницы: 234

Бренд: hepco & becker Страницы: 2

Бренд: DYNATEK Страницы: 12

2004 Moto Matrix

Бренд: Yamaha Страницы: 41

Бренд: Yamaha Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды