Yamaha Star XVS13AA(C) 2011, Руководство по обслуживанию

Страница: 113 / 536

CABLE ROUTING (for XVS13CA(C))
2-86
1. Clutch cable
2. Rear cylinder spark plug lead
3. Canister purge hose (California only)
4. Rear cylinder ignition coil
5. Coolant reservoir hose
6. Wire harness
7. Right handlebar switch coupler
8. Fuel tank overflow hose
9. Throttle cable (accelerator cable)
10. Throttle cable (decelerator cable)
11. Radiator fan motor lead
12. Intake air pressure sensor hose
13. Rear brake light switch
14. Horn
15. Horn lead
16. Rear brake light switch lead
17. Brake fluid reservoir hose
18. Rear brake hose
19. Rear brake light switch coupler
20. Throttle position sensor lead
A. Fasten the clutch cable and coolant reservoir hose
with the holder. Face the catch of the holder
outward.
B. Route the clutch cable to the outside of the coolant
reservoir hose.
C. Route the clutch cable, throttle position sensor
lead, coolant reservoir hose, and rear cylinder
spark plug lead in the order listed from left to right.
Route the throttle position sensor lead under the
frame.
D. Route the coolant reservoir hose to the outside of
the wire harness and right handlebar switch lead,
and under the fuel tank bracket.
E. Route the wire harness under the fuel tank
bracket.
F. Route the right handlebar switch lead over the fuel
tank bracket.
G. Route the fuel tank overflow hose to the outside of
the wire harness, right handlebar switch lead, and
coolant reservoir hose.
H. To fuel tank
I.
Route the fuel tank overflow hose to the outside of
the throttle cables. (Except for California) Route
the throttle cables, canister purge hose, and fuel
tank overflow hose in the order listed from left to
right. (California only)
J. Route the throttle cables to the outside of the wire
harness and radiator fan motor lead.
K. Secure the plastic band by inserting the projection
on the band into the hole in the frame, and then
fasten the wire harness, right handlebar switch
lead, and throttle cables with the band. Align the
tape on the wire harness and right handlebar
switch lead with the plastic band. Cut off the
excess end of the plastic band. Route the throttle
cable (accelerator cable) over the throttle cable
(decelerator cable).
L. Fasten the horn lead and rear brake light switch
lead to the frame with a plastic locking tie. Point the
end of the plastic locking tie downward, and then
cut off the excess end of the tie.
M. Fasten the horn lead and rear brake light switch
lead to the frame with a plastic locking tie. Point the
end of the plastic locking tie downward, and then
cut off the excess end of the tie. Align the plastic
locking tie with the rear end of the right footrest
bracket.
N. Fasten the horn lead, rear brake light switch lead,
rear brake hose, and brake fluid reservoir hose to
the frame with the plastic band. Position the plastic
band under the exhaust pipe protector screw
clamp. Point the end of the plastic band downward.
Make sure that the horn lead and rear brake light
switch lead do not protrude below the frame.
O. Secure the plastic band by inserting the projection
on the band into the hole in the coolant reservoir
cover bracket, and then fasten the horn lead, rear
brake light switch lead, rear brake hose, and brake
fluid reservoir hose with the band.
P. Align the white paint mark on the brake fluid
reservoir hose with the plastic band.
Q. Position the rear brake light switch coupler to the
inside of the rear brake hose and brake fluid
reservoir hose.
R. Be sure to install the throttle cable (decelerator
cable), identified by the longer nut, on the outer
side of the throttle cable pulley.
S. Secure the holder by inserting the projection on
the holder into the hole in the rider footrest
assembly, and then fasten the horn lead and rear
brake light switch lead with the holder.
T. Fasten the horn lead and rear brake light switch
lead with a plastic locking tie. Make sure that the
horn lead and rear brake light switch lead do not
protrude below the frame.
U. Position the buckle of the plastic locking tie within
the range shown in the illustration.