Yamaha Star XV19MY Скачать руководство пользователя | Manualshive

Страница: 32 / 94

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-16

4

WARNING

EWA10221

This shock absorber assembly con-
tains highly pressurized nitrogen
gas. Read and understand the fol-
lowing information before handling
the shock absorber assembly.

●

Do not tamper with or attempt to
open the cylinder assembly.

●

Do not subject the shock ab-
sorber assembly to an open
flame or other high heat source.
This may cause the unit to ex-
plode due to excessive gas
pressure.

●

Do not deform or damage the
cylinder in any way. Cylinder
damage will result in poor
damping performance.

●

Do not dispose of a damaged or
worn-out shock absorber as-
sembly yourself. Take the shock
absorber assembly to a Yamaha
dealer for any service.

EAU15281

EXUP system

This model is equipped with Yamaha’s
EXUP (EXhaust Ultimate Power valve)
system. This system boosts engine
power by means of a valve that regu-
lates the diameter of the exhaust pipe.
The EXUP system valve is constantly
adjusted in accordance with the engine
speed by a computer-controlled servo-
motor.

NOTICE

ECA10191

●

The EXUP system has been set
and extensively tested at the
Yamaha factory. Changing
these settings without sufficient
technical knowledge may result
in poor performance of or dam-
age to the engine.

●

If the EXUP system cannot be
heard when the main switch is
turned on, have a Yamaha deal-
er check it.

EAU15301

Sidestand

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

TIP

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)

WARNING

EWA10240

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described

U1D713E0.book Page 16 Monday, June 23, 2008 2:53 PM

«
...
30
31
32
33
34
...
»

Содержание Star XV19MY































































































Отзывы:

Нет отзывов

Похожие инструкции для Star XV19MY

Бренд: LSL Страницы: 4

Бренд: MSA Страницы: 163

Бренд: Honda Страницы: 325

Бренд: Serpento Страницы: 66

Бренд: Bosch Страницы: 160

Бренд: VESPA Страницы: 249

Бренд: Shad Страницы: 2

KIT TOPMASTER S0BN11ST

Бренд: Shad Страницы: 2

KIT TOPMASTER S0SV69ST

Бренд: Shad Страницы: 2

KIT TOPMASTER S0GL69ST

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

TOPMASTER H0PC10ST

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Engelbert Strauss Страницы: 46

Бренд: BMS Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды