background image

OPERATION AND IMPORTANT RIDING POINTS

6-3

6

4. At the recommended shift points

shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.

5. Shift the transmission into second

gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)

6. Open the throttle part way and

gradually release the clutch lever.

7. Follow the same procedure when

shifting to the next higher gear.

TIP

When shifting gears in normal operat-
ing conditions, use the recommended
shift points.

EAU16700

To decelerate

1. Apply both the front and the rear

brakes to slow the motorcycle.

2. Shift the transmission into first

gear when the motorcycle reaches
25 km/h (16 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu-

tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.

EAU16720

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

EAU16841

Engine break-in 

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17112

0–1000 km (0–600 mi)

Avoid prolonged operation above 2500
r/min. 

NOTICE:

 After 1000 km (600

mi) of operation, the engine oil and
transfer case oil must be changed,
and the oil filter cartridge or element
replaced.

 [ECA10892]

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 3500
r/min.

Shift up points:

1st 

 2nd: 20 km/h (13 mi/h)

2nd 

 3rd: 30 km/h (19 mi/h)

3rd 

 4th: 40 km/h (25 mi/h)

4th 

 5th: 50 km/h (31 mi/h)

Shift down points:

5th 

 4th: 25 km/h (16 mi/h)

4th 

 3rd: 25 km/h (16 mi/h)

3rd 

 2nd: 25 km/h (16 mi/h)

2nd 

 1st: 25 km/h (16 mi/h)

U1D713E0.book  Page 3  Thursday, May 8, 2008  4:19 PM

Содержание Star XV19MY































































































Отзывы: