Yamaha Star 2010 страница 41 Скачать руководство пользователя | Manualshive

Страница: 41 / 104

background image

OPERATION AND IMPORTANT RIDING POINTS

6-2

6

NOTICE

ECA15484

If a warning light does not come on
initially when the key is turned to
“ON”, or if a warning light remains
on, see page 4-2 for the correspond-
ing warning light circuit check.

2. Shift the transmission into the neu-

tral position. The neutral indicator
light should come on. If not, ask a
Yamaha dealer to check the elec-
trical circuit.

3. Start the engine by pushing the

start switch.
If the engine fails to start, release
the start switch, wait a few sec-
onds, and then try again. Each
starting attempt should be as short
as possible to preserve the bat-
tery. Do not crank the engine more
than 10 seconds on any one at-
tempt.

NOTICE

ECA11042

For maximum engine life, never ac-
celerate hard when the engine is
cold!

EAU16671

Shifting

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.

TIP

To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

NOTICE

ECA10260

●

Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.

●

Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.

EAU16681

To start out and accelerate

1. Pull the clutch lever to disengage

the clutch.

2. Shift the transmission into first

gear. The neutral indicator light
should go out.

3. Open the throttle gradually, and at

the same time, release the clutch
lever slowly.

1. Shift pedal

2. Neutral position

1

5
4
3
2

N

1

5
4
3
2

N

1

2

U5S614E0.book Page 2 Friday, July 9, 2010 9:18 AM

«
...
39
40
41
42
43
...
»

Содержание Star 2010









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star 2010

Бренд: Cake Страницы: 13

Бренд: Big Bike Parts Страницы: 2

Rocky Mountain-EXP SB-1

Бренд: Wolfman Страницы: 7

Grizzly Minicross RCX/12 50CC

Бренд: Malaguti Страницы: 33

Бренд: hepco & becker Страницы: 4

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 4

Lectra VR24 1998

Бренд: EMB Страницы: 58

RT125D - PARTS CATALOGUE

Бренд: HYOSUNG Страницы: 73

Ranger XP900 A-Arms

Бренд: SuperATV Страницы: 6

Бренд: Beta Страницы: 260

Бренд: Petzl Страницы: 13

Бренд: Kemimoto Страницы: 3

Бренд: Bikecomm Страницы: 15

Бренд: Indian Motorcycle Страницы: 134

Бренд: Rothewald Страницы: 50

Бренд: Rivco Страницы: 5

Бренд: Rivco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды