Yamaha Star 2010 Скачать руководство пользователя | Manualshive

Страница: 20 / 104

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-2

4

To unlock the steering

Push the key in, and then turn it to
“OFF” while still pushing it.

EAU49391

Indicator lights and warning
lights

EAU11020

Turn signal indicator light “

”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11254

Oil level warning light “

”

This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

●

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If a problem
is detected in the oil level detection

1. Push.
2. Turn.

1. Neutral indicator light “

”

2. Coolant temperature warning light “

”

3. Engine trouble warning light “

”

4. High beam indicator light “

”

5. Turn signal indicator light “

”

6. Oil level warning light “

”

7. Fuel level warning light “

”

U5S614E0.book Page 2 Friday, July 9, 2010 9:18 AM

«
...
18
19
20
21
22
...
»

Содержание Star 2010









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star 2010

Бренд: R&G Страницы: 14

Бренд: FDC Страницы: 6

Бренд: Cobra Страницы: 80

Бренд: National Cycle Страницы: 2

Бренд: LAS Страницы: 22

Бренд: Yamaha Страницы: 9

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 91

Бренд: Yamaha Страницы: 92

Virago XV250 2004

Бренд: Yamaha Страницы: 95

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 114

V-Star XVS1100ATC

Бренд: Yamaha Страницы: 110

V-Star XVS1100AR

Бренд: Yamaha Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды