Yamaha SR10RE Скачать руководство пользователя страница 20

Страница: 20 / 52

2. When the lubricant has completely

drained from the case and the chain

case is cleaned of old oil, install the

chain case cover. Tighten the cap

screws to 1.2 kg-m (105 in.-lb).

XM092

3. Remove the three screws securing

the shift actuator to the chain case,

disconnect the actuator wiring har-

ness, and remove the actuator w/

extension. Pour the recommended

chain lubricant through the shift

actuator opening until the lubricant

is at least halfway up in the sight

glass; then install the shift actuator

w/extension and connect the actua-

tor wiring harness.



NOTE: Make sure the reverse sen-

sor wire is routed up so the wires do

not become pinched between the

actuator and the case.

4. Install and secure the exhaust reso-

nator.

5. Start the engine and verify proper

reverse and forward operation by

shifting in and out of reverse three

times.

Rear Suspension

This procedure should be done every 40

operating hours.



NOTE: Yamaha recommends that

All-Temp Grease be used for this

procedure.

1. Using Handlebar Stand or Steering

Post Stand or a suitable substitute,

lay the snowmobile on its left side.

2. Lubricate all grease fittings with all-

temperature grease.

CAUTION

Before installing the chain case screws,

be sure to clean the holes using com-

pressed air completely of debris or

damage to the chain case may occur.

CAUTION

When installing the shift actuator,

rotate the actuator back and forth to

properly align it with the extension

gear. Failure to do so could cause

component damage.

CAUTION

The correct lubricant to use in the

chain case is Synthetic Chain Lube.

Any substitute may cause serious

damage to the drive system.

Содержание SR10RE





















































Результаты поиска

Содержание SR10RE

Отзывы:

Похожие инструкции для SR10RE

Бренды по названию

Популярные бренды

Yamaha SR10RE, Руководство оператора

Результаты поиска

Содержание SR10RE

Отзывы:

Похожие инструкции для SR10RE

Бренды по названию

Популярные бренды