Yamaha RM1x Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 54

background image

31

RM1x

OUTPUT (

L

)

:

1 kHz +/- 3.0 Hz, Sine wave

+2 +/- 2 dBm (10 kHz load),
Distortion : less than 0.5%

OUTPUT (

R

)

:

less than -76 dBm

PHONES (

L

)

:

5 +/- 2 dBm (33 ohm load),
Distortion : less than 0.5%

PHONES (

R

)

:

less than -68 dBm

The LCD display during the sound output.

Display Of Test Results
Not appearing

Test End

Press the [F4] switch to finish the test.
After press the [F4] switch to exit the test, press
the [+1] switch to proceed with the next test and
then the [ENTER] switch to execute the next test.

C-23 PCM SINE WAVE 1kHz OUTPUT

(R) TEST

The VOLUME control must be set at maximum.
Insert the appropriate phone plugs into each
output jack and check the OUTPUT (L, R),
PHONES (L, R) outputs. If necessary, verify the
frequency, output waveform and output level of
each output using a frequancy countor,
oscilloscope and AC voltmeter (with JIS-C filter).
Listed below are the specifications and
conditions of each output during this test.

OUTPUT (

R

)

:

1 kHz +/- 3.0 Hz, Sine wave
+2 +/- 2 dBm (10 kHz load),
Distortion : less than 0.5%

OUTPUT (

L

)

:

less than -76 dBm

PHONES (

R

)

:

5 +/- 2 dBm (33 ohm load)

Distortion : less than 0.5%

PHONES (

L

)

:

less than -68 dBm

The LCD display during the sound output.

Display Of Test Results
Not appearing

Test End

Press the [F4] switch to finish the test.
After press the [F4] to exit the test, press the
[+1] switch to proceed with the next test and
then the [ENTER] switch to execute the next test.

C-24. FACTORY SETTINGS

This test is used to initialize the following data to
the factory settings.

System Data
Song Data
Sequence data

When this test is executed, the following
display will appear.

[YES] : execute the factory settings.
[NO] : not execute the factory settings.

Display Of Test Results
When the factory set is set.

When the factory set is not set.

Test End

After displaying the test result the test will be
finished.
After press the [F4] to exit the test, press the
[+1] switch to proceed with the next test and
then the [ENTER] switch to execute the next
test.

At this time, each data are set as follows.

Master Tune fine =

0

Foot Switch Assign =

Start Stop

Pattern Change quantize = 16

’

s note

Memory protect =

OFF

LED Display =

BPM display

LCD Mode =

POSI

MTC Start Offset =

00:00:00:00

Metronome =

REC

Click Beat =

4

’

s note

Interval Time =

100 ms

Edit Event List TG View = ON

MIDI SYNC =

Internal

MIDI Control =

Out

Echo Back =

Thru

MIDI Filter in =

All Receive

MIDI Filter out =

All Transmit

TG Parameter =

OFF

Voice Setup to TG =

ON

24: Factory Set

22: PCM SIN 1kHz L
ON

24: Factory Set

[NO] or [YES] ?

24: Factory Set
OK

23: PCM SIN 1kHz R

24: Factory Set
not set

23: PCM SIN 1kHz R
ON

«
...
27
28
29
30
31
...
»

Содержание RM1x























































Отзывы:

Нет отзывов

Похожие инструкции для RM1x

Бренд: Tesla Страницы: 44

Бренд: AKG Страницы: 79

Бренд: Cole Parmer Страницы: 64

Бренд: Aviom Страницы: 93

JSM900EAAU - Jenn-Air Attrezzi Antique Copper Stand...

Бренд: Jenn-Air Страницы: 56

Бренд: Sound Acoustics Страницы: 5

Бренд: Litchi Страницы: 12

Бренд: Numark Страницы: 12

Бренд: Boston Acoustics Страницы: 18

Бренд: PROEL Страницы: 30

171.142 PDM-S803

Бренд: Power Dynamics Страницы: 16

Бренд: Proctor-Silex Страницы: 20

Бренд: Probox Страницы: 63

Бренд: Heston Blumenthal Страницы: 24

Бренд: Executive Audio Страницы: 5

PRODUCTION VIEW 999-5650-000

Бренд: VADDIO Страницы: 24

Бренд: Denon Страницы: 104

Platinum PS-727

Бренд: Gemini Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды