MX49/MX61 Reference Manual
51
This display appears only when a Normal Voice is assigned to the selected Part.
Voice LFO
Parameter
Description
Wave
(LFO Wave)
Selects the LFO waveform.
Settings:
tri (triangle), tri+ (t), sawup, sawdwn, squ1/4 (square1/4), squ1/3 (square1/3), squ
(square), squ2/3 (square2/3), squ3/4 (square3/4), trpzd (trapezoid), S/H 1 (sample & hold 1), S/H 2 (sample
& hold 2), user
NOTE
The “user” wave is a special waveform which is assigned to some Preset Voices. You can create an original
LFO wave by receiving MIDI messages from an external device. For details, see “MIDI Data Table” in the
“Data List” PDF document.
Speed
Adjusts the speed (frequency) of LFO variation.
Settings:
0 – 63
TempoSync
Determines whether or not the LFO is synchronized to the tempo of the Arpeggio or sequencer (Song or
Pattern).
Settings:
off (not synchronized), on (synchronized)
TempoSpeed
This parameter is available only when “TempoSync” above has been set to “on.” It allows you to make
detailed note value settings that determine how the LFO pulses in sync with the Arpeggio.
Settings:
16th, 8th/3 (eighth-note triplets), 16th. (dotted sixteenth notes), 8th, 4th/3 (quarter-note triplets),
8th. (dotted eighth notes), 4th (quarter notes), 2nd/3 (half-note triplets), 4th. (dotted quarter notes), 2nd (half
notes), whole/3 (whole-note triplets), 2nd. (dotted half notes), 4th x 4 (quarter-note quadruplets; four quarter
notes to the beat), 4th x 5 (quarter-note quintuplets; five quarter notes to the beat), 4th x 6 (quarter-note
sextuplets; six quarter notes to the beat), 4th x 7 (quarter-note septuplets; seven quarter notes to the beat),
4th x 8 (quarter-note octuplets; eight quarter notes to the beat), 4th x 16 (sixteen quarter-notes to the beat),
4th x 32 (32 quarter notes to the beat), 4th x 64 (64 quarter notes to the beat)
NOTE
The actual length of the note depends on the internal or external MIDI tempo setting.
PlayMode
Determines whether the LFO cycles repeatedly (loop) or only once (one shot).
Settings:
loop, one shot
KeyOnRest
(Key On Reset)
Determines whether or not the LFO is reset each time a note is pressed.
Settings:
off, each-on, 1st-on
RandomSpeed
This parameter is available only when “TempoSync” above has been set to “off.” Determines the degree to
which the LFO speed changes at random.
Settings:
0 – 127
Delay
Determines the delay time between the moment you press a key on the keyboard and the moment the LFO
comes into effect.
Settings:
0 – 127
Fade In
(Fade In Time)
Determines the amount of time for the LFO effect to fade in (after the “Delay” time has elapsed).
Settings:
0 – 127
Hold
(Hold Time)
Determines the length of time during which the LFO is held at its maximum level.
Settings:
0 – 126, hold
FadeOut
(Fade Out Time)
Determines the time over which the LFO effect is faded out (after the “Hold” time has elapsed).
Settings:
0 – 127
Dest1/2/3
(LFO Set 1/2/3 Control
Destination)
Determines the functions which will be controlled by the LFO Wave.
Settings:
See the “Control List” in the “Data List” PDF document.
NOTE
Regarding “Insertion Effect Parameter 1 - 16” described in the Control List, the actual parameter names of
the selected Effect type are shown on the display. If “P*” is shown on the display, no function is assigned to
that parameter. The “*” mark indicates the parameter number.
Depth1/2/3
(LFO Set 1/2/3 Control
Depth)
Set the LFO Wave Depth.
Settings:
0 – 127
