Yamaha MBK MW125 2014 Скачать руководство пользователя страница 98

Страница: 98 / 380

PERIODIC MAINTENANCE

3-17

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

7. Install:

• Handlebar

Refer to “HANDLEBAR” on page 4-60.

• Front cowling assembly

Refer to “GENERAL CHASSIS (7)” on page
4-14.

EAS31184

CHECKING THE TIE-ROD BUSHINGS AND
FRONT ARM BUSHINGS

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

2. Elevate:

• Front wheels

Refer to “REMOVING THE FRONT
WHEELS” on page 4-28.

3. Check:

• Tie-rod bushings and front arm bushings

While holding the front portions of the left and
right front wheels, move the wheels to the left
and right and check for looseness.

Looseness

→

Tighten the tie-rod nuts, tie-rod

joint bolts, and front arm bolts.
Refer to “FRONT ARMS AND LOWER
BRACKETS” on page 4-76.

TIP

If there is still looseness after tightening the tie-
rod nuts, tie-rod joint bolts, and front arm bolts,
replace the tie rod and/or front arm.

EAS31185

CHECKING THE LINK ARM BEARINGS

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

2. Elevate:

• Front wheels

Refer to “REMOVING THE FRONT
WHEELS” on page 4-28.

3. Check:

• Link arm bearings

Hold the front fork legs and move them up
and down to check the front forks for smooth
operation.

Operation is not smooth

→

Tighten the link

arm bolts.
Refer to “STEERING HEAD” on page 4-81.

TIP

If the operation is not smooth after tightening the
link arm bolts, replace the link arm bearings.

EAS31186

CHECKING THE CHASSIS FASTENERS

Make sure that all nuts, bolts, and screws are
properly tightened.
Refer to “CHASSIS TIGHTENING TORQUES”
on page 2-15.

EAS30648

LUBRICATING THE LEVERS

Lubricate the pivoting point and metal-to-metal
moving parts of the levers.

EAS30650

CHECKING THE SIDESTAND

1. Check:

• Sidestand operation

Check that the sidestand moves smoothly.
Rough movement

→

Repair or replace.

Steering nut wrench

90890-01403

Exhaust flange nut wrench

YU-A9472

Upper ring nut

75 Nm (7.5 m·kgf, 54 ft·lbf)

Recommended lubricant

Silicone grease

Содержание MBK MW125 2014





























































































































































































































































































































































































Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды

Yamaha MBK MW125 2014, Руководство по обслуживанию

Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды