Yamaha MBK MW125 2014 Скачать руководство пользователя страница 137

Страница: 137 / 380

FRONT WHEELS

4-28

EAS30145

REMOVING THE FRONT WHEELS

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

• Front brake calipers

NOTICE

ECA21620

Do not operate the brake lever when remov-
ing the brake calipers.

3. Elevate:

• Front wheels

TIP

Be sure to place the stand “1” under the vehicle
at the location shown in the illustration.

EAS30146

DISASSEMBLING THE FRONT WHEELS

The following procedure applies to both of the
front wheels.
1. Remove:

• Oil seals
• Wheel bearings

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Clean the surface of the front wheel hub.
b. Remove the oil seals “1” with a flat-head

screwdriver.

TIP

To prevent damaging the wheel, place a rag “2”
between the screwdriver and the wheel surface.

c. Remove the wheel bearings “3” with a gener-

al bearing puller.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS30147

CHECKING THE FRONT WHEELS

The following procedure applies to both of the
front wheels.
1. Check:

• Wheel axle

Roll the wheel axle on a flat surface.
Bends

→

Replace.

WARNING

EWA13460

Do not attempt to straighten a bent wheel ax-
le.

2. Check:

• Tire
• Front wheel

Damage/wear

→

Replace.

Refer to “CHECKING THE TIRES” on page
3-14 and “CHECKING THE WHEELS” on
page 3-13.

3. Measure:

• Radial wheel runout “1”
• Lateral wheel runout “2”

Over the specified limits

→

Replace.

Radial wheel runout limit

1.0 mm (0.04 in)

Lateral wheel runout limit

0.5 mm (0.02 in)

Содержание MBK MW125 2014





























































































































































































































































































































































































Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды

Yamaha MBK MW125 2014, Руководство по обслуживанию

Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды