Yamaha KODIAK 700 2018 страница 125 Скачать руководство пользователя

Страница: 125 / 180

8-27

To check the differential gear oil level

1. Park the ATV on a level surface.
2. Remove the differential gear oil filler bolt and

its gasket, and then check the oil level in the
differential gear case. The oil level should be
at the brim of the filler hole.

3. If the oil is below the brim of the filler hole, add

sufficient oil of the recommended type to
raise it to the correct level.

4. Check the gasket for damage, and replace it

if necessary.

5. Install the oil filler bolt and its gasket, and then

tighten the bolt to the specified torque.

To change the differential gear oil

1. Park the ATV on a level surface.
2. Place an oil pan under the differential gear

case to collect the used oil.

3. Remove the differential gear oil filler bolt, the

differential gear oil drain bolt and their gasket
to drain the oil from the differential gear case.

1. Differential gear oil filler bolt
2. Gasket
3. Differential gear oil
4. Correct oil level

1 2

Tightening torque:

Differential gear oil filler bolt:

23 N·m (2.3 kgf·m, 17 lb·ft)

1. Differential gear oil drain bolt
2. Gasket

UB5K60E0.book Page 27 Monday, May 28, 2018 11:35 AM

Содержание KODIAK 700 2018





















































































































































































Результаты поиска

Содержание KODIAK 700 2018

Отзывы:

Похожие инструкции для KODIAK 700 2018

Бренды по названию

Популярные бренды

Yamaha KODIAK 700 2018, Руководство пользователя

Результаты поиска

Содержание KODIAK 700 2018

Отзывы:

Похожие инструкции для KODIAK 700 2018

Бренды по названию

Популярные бренды