Yamaha KODIAK 700 2018 Скачать руководство пользователя

Страница: 126 / 180

8-28

4. Install the drain bolt and its new gasket, and

then tighten the bolt to the specified torque.

5. Refill with the recommended differential gear

oil to the brim of the filler hole as shown.

NOTICE:

Be sure no foreign material en-

ters the differential gear case.

[ECB00412]

6. Check the oil filler bolt gasket for damage,

and replace it if necessary.

7. Install the oil filler bolt and its gasket, and then

tighten the bolt to the specified torque.

8. Check the differential gear case for oil leak-

age. If oil is leaking, check for the cause.

EBU23472

Coolant

The coolant level should be checked regularly. In
addition, the coolant must be changed at the in-
tervals specified in the periodic maintenance and
lubrication chart.

Tightening torque:

Differential gear oil drain bolt:

9.8 N·m (0.98 kgf·m, 7.2 lb·ft)

1. Differential gear oil filler bolt
2. Gasket
3. Differential gear oil
4. Correct oil level

1 2

Recommended differential gear oil:

See page 10-1.

Tightening torque:

Differential gear oil filler bolt:

23 N·m (2.3 kgf·m, 17 lb·ft)

UB5K60E0.book Page 28 Monday, May 28, 2018 11:35 AM

Содержание KODIAK 700 2018





















































































































































































Результаты поиска

Содержание KODIAK 700 2018

Отзывы:

Похожие инструкции для KODIAK 700 2018

Бренды по названию

Популярные бренды

Yamaha KODIAK 700 2018, Руководство пользователя

Результаты поиска

Содержание KODIAK 700 2018

Отзывы:

Похожие инструкции для KODIAK 700 2018

Бренды по названию

Популярные бренды