Yamaha GX-700VCD, Руководство пользователя

Страница: 38 / 52

E-30
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT
D
PRESET
+
I0
E
MODE REPEAT RANDOM TUNER
DISC SKIP
DIRECTION
CENTER/
REAR/DELAY TEST PROGRAM
BASS
BOOST MUSIC
POWER SLEEP
INPUT VOLUME
A B
TAPE
LEVEL
/I
KEY/ECHO
SELECT RETURN TIME INDEX
DIGEST KARAOKE INTRO
TUNER
VCD / CD
REC/PAUSE
DISC
1
DISC
2
DISC
3
DOWN UP
VOLUME
STANDBY/ON
PROGRAM B.BOOST MUSIC
INPUT INPUT
MIN
PRESET/ TUNING/ BAND A/B/C/D/E
DISC CHANGE OPEN / CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSE DOLBY NR
HOUR
RANDOM REPEAT TIME
DISPLAY MODE
KARAOKE
Recording
m
Manual EDIT recording
You can program tracks manually while watching the
remaining time on both sides of the tape.
1
Press INPUT or once or more until “VCD/CD” (
1
)
appears on the display, and load a disc (or discs) on the
disc tray.
2
Follow steps 3–5 on page 29.
3
Press PROG.
* “PROG” and “P-01” will light up on the display, and all
track numbers on the selected disc will begin flashing.
4
If necessary, select the desired disc by pressing DISC
SKIP.
5
Select the desired track number by pressing the numeric
buttons.
6
Repeat steps 4 and 5 to program more selections for side A
of the tape. You can select the same track again.
* Pressing TIME displays the total remaining time on side
A of the tape for about 1 second, and then it is replaced
by the display of the next play order.
* If “TM OVER” appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program it
instead of the unprogrammable one.
7
When the programming for side A is finished, press
R. TIME.
* “Side–B” appears on the display. You can begin
programming for side B.
* After following this step, you can check the programmed
contents for side A and side B alternately by pressing
R. TIME at any time before you press EDIT in step 9.
* The tape side indicator (
9
) shows the programming
side currently selected.
8
Repeat steps 4 and 5 to program selections for side B of
the tape. You can select the same track again.
9
Press EDIT. (“EDIT” (
8
) lights up on the display.)
The recording starts.
1
1
3
4
5
7
9
Display information during programming
Notes on recording with the EDIT function
●
To check, cancel or correct program data, refer to page 15.
●
The maximum number of tracks that can be programmed is
20.
●
The track number 16 or higher cannot be programmed by
this function.
TIME
TIME
Selected disc
Side of the tape Next play order
Programmed track numbers light up and
only programmable track numbers
among unprogrammed ones flash.
Total remaining time on
this side of the tape
Selected track
number
M
PROG VOLUME
A
OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
REM
TRACK
CD
NR
M
HALL
MERSION
EDIT
PROG
S F REP
VOLUME
A B
OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM TUNER
CD
MD
TAPE
NR
Display information during programming