Yamaha GRIZZLY 700 FI YFM7FGPX страница 114 Скачать руководство пользователя

Страница: 114 / 164

8-29

2. Remove the differential gear oil filler bolt, and

then check the oil level in the differential gear
case.

NOTE:

The oil level should be at the brim of the filler hole.

3. If the oil is below the brim of the filler hole, add

sufficient oil of the recommended type to raise
it to the correct level.

4. Install the oil filler bolt, and then tighten it to the

specified torque.

To change the differential gear oil

1. Place the ATV on a level surface.
2. Place an oil pan under the differential gear

case to collect the used oil.

3. Remove the differential gear oil filler bolt and

the differential gear oil drain bolt to drain the
oil from the differential gear case.

4. Install the drain bolt, and then tighten it to the

specified torque.

1. Differential gear oil
2. Differential gear oil filler bolt

3. Correct oil level

Tightening torque:

Differential gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

1. Differential gear oil drain bolt

U3B462E0.book Page 29 Tuesday, March 20, 2007 11:46 AM

Содержание GRIZZLY 700 FI YFM7FGPX





































































































































































Результаты поиска

Содержание GRIZZLY 700 FI YFM7FGPX

Отзывы:

Похожие инструкции для GRIZZLY 700 FI YFM7FGPX

Бренды по названию

Популярные бренды

Yamaha GRIZZLY 700 FI YFM7FGPX, Руководство пользователя

Результаты поиска

Содержание GRIZZLY 700 FI YFM7FGPX

Отзывы:

Похожие инструкции для GRIZZLY 700 FI YFM7FGPX

Бренды по названию

Популярные бренды