Yamaha GRIZZLY 700 FI YFM7FGPX страница 108 Скачать руководство пользователя

Страница: 108 / 164

8-23

NOTE:

The engine oil should be between the minimum
and maximum level marks.

6. If the engine oil is at or below the minimum

level mark, add sufficient oil of the recom-
mended type to raise it to the correct level.

7. Insert the dipstick completely into the oil filler

hole.

8. Install the panel.

CAUTION:

ECB00850

Be sure the engine oil is at the correct level,
otherwise engine damage may result.

To change the engine oil (with or without oil fil-
ter cartridge replacement)

1. Place the ATV on a level surface.
2. Remove panel F. (See page 8-8.)
3. Place an oil pan under the engine to collect

the used oil.

4. Remove the dipstick, and then remove the en-

gine oil drain bolt to drain the oil from the
crankcase.

1. Maximum level mark
2. Minimum level mark

1. Engine oil drain bolt

U3B462E0.book Page 23 Tuesday, March 20, 2007 11:46 AM

Содержание GRIZZLY 700 FI YFM7FGPX





































































































































































Результаты поиска

Содержание GRIZZLY 700 FI YFM7FGPX

Отзывы:

Похожие инструкции для GRIZZLY 700 FI YFM7FGPX

Бренды по названию

Популярные бренды

Yamaha GRIZZLY 700 FI YFM7FGPX, Руководство пользователя

Результаты поиска

Содержание GRIZZLY 700 FI YFM7FGPX

Отзывы:

Похожие инструкции для GRIZZLY 700 FI YFM7FGPX

Бренды по названию

Популярные бренды