Yamaha FZS10Z Скачать руководство пользователя страница 86

Страница: 86 / 110

PERIODIC MAINTENANCE AND ADJUSTMENT

7-38

5. Turn the drive chain slack adjust-

ing bolts fully in direction (a) and
push the wheel forward.

6. Remove the drive chain from the

rear sprocket.

TIP

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain cannot be disas-
sembled.

7. While supporting the brake caliper

bracket, pull the wheel axle out,
and then remove the wheel.

NOTICE:

Do not apply the brake

after the wheel has been re-
moved together with the brake
disc, otherwise the brake pads
will be forced shut.

[ECA11071]

EAU39412

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the left-hand side.

TIP

●

Make sure that the slot in the brake
caliper bracket is fit over the retain-
er on the swingarm.

●

Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

2. Install the drive chain onto the rear

sprocket.

3. Install the axle nut.
4. Lower the rear wheel so that it is

on the ground, and then put the
sidestand down.

5. Adjust the drive chain slack. (See

page 7-25.)

6. Tighten the axle nut to the speci-

fied torque.

1. Drive chain slack adjusting bolt
2. Locknut

(a)

1. Wheel axle

1. Slot
2. Retainer

Tightening torque:

Axle nut:

150 Nm (15 m·kgf, 108 ft·lbf)

U1CA10E0.book Page 38 Tuesday, November 24, 2009 1:41 PM

Содержание FZS10Z















































































































Результаты поиска

Содержание FZS10Z

Отзывы:

Похожие инструкции для FZS10Z

Бренды по названию

Популярные бренды

Yamaha FZS10Z, Руководство пользователя

Результаты поиска

Содержание FZS10Z

Отзывы:

Похожие инструкции для FZS10Z

Бренды по названию

Популярные бренды