Yamaha FZS10Z Скачать руководство пользователя страница 83

Страница: 83 / 110

PERIODIC MAINTENANCE AND ADJUSTMENT

7-35

3. Remove the burnt-out bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the turn signal light unit by

installing the screw.

NOTICE:

not overtighten the screw, oth-
erwise the lens may break.

[ECA11191]

EAU24313

Replacing the license plate
light bulb

1. Remove the license plate light unit

by removing the screws.

2. Remove the license plate light bulb

socket (together with the bulb) by
pulling it out.

1. Turn signal light bulb socket

1. Turn signal light bulb

1. License plate light unit

2. Screw

U1CA10E0.book Page 35 Tuesday, November 24, 2009 1:41 PM

Содержание FZS10Z















































































































Результаты поиска

Содержание FZS10Z

Отзывы:

Похожие инструкции для FZS10Z

Бренды по названию

Популярные бренды

Yamaha FZS10Z, Руководство пользователя

Результаты поиска

Содержание FZS10Z

Отзывы:

Похожие инструкции для FZS10Z

Бренды по названию

Популярные бренды