Yamaha FZ6RD(C) Скачать руководство пользователя страница 85

Страница: 85 / 118

PERIODIC MAINTENANCE AND ADJUSTMENT

7-36

is turned to “OFF”, then con-
nect the positive lead before
connecting the negative lead.

[ECA16840]

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

NOTICE

ECA16530

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

EAU47470

Replacing the fuses

The main fuse and the fuse box, which
contains the fuses for the individual cir-
cuits, are located under the rider seat.
(See page 4-14.)

TIP

To access the main fuse, remove the
starter relay cover as shown.

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

WARNING! Do not

use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.

[EWA15131]

1. Starter relay cover
2. Main fuse

3. Spare main fuse

4. Fuse box

1. Spare fuse
2. Headlight fuse

3. Ignition fuse

4. Signaling system fuse
5. Backup fuse (for clock)

6. Fuel injection system fuse

7. Radiator fan fuse

U36P14E0.book Page 36 Thursday, August 2, 2012 2:13 PM

Содержание FZ6RD(C)























































































































Результаты поиска

Содержание FZ6RD(C)

Отзывы:

Бренды по названию

Популярные бренды

Yamaha FZ6RD(C), Руководство пользователя

Результаты поиска

Содержание FZ6RD(C)

Отзывы:

Бренды по названию

Популярные бренды