manualshive.com logo in svg

Yamaha FZ6RD(C), Руководство пользователя

Поделиться
Скачать
Yamaha FZ6RD(C) Скачать руководство пользователя страница 49

OPERATION AND IMPORTANT RIDING POINTS

6-4

6

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

NOTICE

ECA10310

●

Keep the engine speed out of
the tachometer red zone.

●

If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.

EAU17213

Parking 

When parking, stop the engine, and
then remove the key from the main
switch.

WARNING

EWA10311

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.

●

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.

●

Do not park near grass or other
flammable materials which
might catch fire.

U36P14E0.book  Page 4  Thursday, August 2, 2012  2:13 PM

Содержание FZ6RD(C)























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды