Yamaha FZ6-ST Скачать руководство пользователя страница 20

Страница: 20 / 469

CHAS

EAS00709

CHASSIS

SWINGARM AND DRIVE CHAIN

CHECKING THE DRIVE CHAIN

1. Measure:

• Measure the dimension between 15-links

on the inner side

and outer side

of the

roller and calculate the dimension between
pin centers.

• Dimension

between pin centers = (Inner

dimension

+ Outer dimension

)/2

• 15-link section

of the drive chain

Out of specification

→

Replace the drive

chain, front drive sprocket and rear drive
sprocket as a set.

NOTE:

• While measuring the 15-link section, push

down on the drive chain to increase its ten-
sion.

• Perform this measurement at two or three dif-

ferent places.

2. Check:

• drive chain

Stiffness

→

Clean and lubricate or replace.

3. Clean:

• drive chain

a. Wipe the drive chain with a clean cloth.
b. Put the drive chain in kerosene and remove

any remaining dirt.

c. Remove the drive chain from the kerosene

and completely dry it.

15-link drive chain section limit

(maximum)

239.3 mm (9.42 in)

SWINGARM AND DRIVE CHAIN

Содержание FZ6-ST






















































































































































































































































































































































































































































































Результаты поиска

Содержание FZ6-ST

Отзывы:

Похожие инструкции для FZ6-ST

Бренды по названию

Популярные бренды

Yamaha FZ6-ST, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание FZ6-ST

Отзывы:

Похожие инструкции для FZ6-ST

Бренды по названию

Популярные бренды