Yamaha FZ6-ST Скачать руководство пользователя страница 438

Страница: 438 / 469

8-33

LIGHTING SYSTEM

ELEC

YES

1. Tail / brake light bulb and socket

Check the tail / brake light bulb and socket for
continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the tail / brake light bulb and socket OK?

Replace the tail /
brake light bulb,
socket or both.

EAS00790

3. The tail / brake light fails to come on.

YES

2. Voltage

Connect the pocket tester (DC 20 V) to the
tail / brake light coupler (wire harness side)
as shown.

Wiring circuit from
the main switch to
the tail / brake light
coupler is faulty and
must be repaired.

Positive tester probe

blue

Negative tester probe

black

Turn the main switch to “ON”.

Measure the voltage (DC 12 V) of blue

the tail / brake light coupler (wire harness
side).

Is the voltage within specification?

This circuit is OK.

EAS00791

4. The turn signal/position light fails to come on.

YES

1. Turn signal / position light and socket

Check the turn signal / position light bulb and
socket for continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the turn signal / position light bulb and
socket OK?

Replace the turn sig-
nal / position light
bulb, socket or both.

YES

2. Voltage

Connect the pocket tester (DC 20 V) to the
turn signal / position light coupler (wire har-
ness side) as shown.

The wiring circuit from
the main switch to the
turn signal/position
light coupler is faulty
and must be repaired.

Turn the main switch to “ON”.

Measure the voltage (DC 12 V) of blue

blue / red

on the turn signal / position light

coupler (wire harness side).

Is the voltage within specification?

This circuit is OK.

Left turn signal / position light

Positive tester probe

blue

Negative tester probe

black

Right turn signal / position light

Positive tester probe

blue / red

Negative tester probe

black

Left turn signal / position light
Right turn signal / position light

A
B

Содержание FZ6-ST






















































































































































































































































































































































































































































































Результаты поиска

Содержание FZ6-ST

Отзывы:

Похожие инструкции для FZ6-ST

Бренды по названию

Популярные бренды

Yamaha FZ6-ST, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание FZ6-ST

Отзывы:

Похожие инструкции для FZ6-ST

Бренды по названию

Популярные бренды