background image

 

Basic components

 

22

 

EMU26332

 

Tilt support bar

 

The tilt support bar keeps the outboard motor
in the tilted up position.

CAUTION:

 

ECM01660 

 

Do not use the tilt support bar when
trailering the boat. The outboard motor
could shake loose from the tilt support
and fall. If the motor cannot be trailered in
the normal running position, use an addi-
tional support device to secure it in the

 

tilt position.

 

EMU26372

 

Top cowling lock lever(s) (turn type)

 

To remove the engine top cowling, turn the
lock lever(s) and lift off the cowling. When in-
stalling the cowling, check to be sure it fits
properly in the rubber seal. Then lock the
cowling again by returning the lever(s) to the
lock position.

 

EMU26460

 

Flushing device

 

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

 

For details on usage, see page 51.

 

EMU26302

 

Warning indicator

 

If the engine develops a condition which is
cause for warning, the indicator lights up. For
details on how to read the warning indicator,
see page 23.

ZMU02292

 

1. Top cowling lock lever(s)

1. Flushing device

ZMU02009

1

ZMU02813

1

Содержание FT25B























































































Отзывы: