Yamaha F80B Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 100

background image

Operation

62

tilt switch “

” (down) to retract the trim

rods.

NOTICE:

Make sure that the trim

rods retracts completely during moor-
ing. This protects the rods from ma-
rine growth and corrosion, which
could damage the power trim and tilt
mechanism.

[ECM00252]

EMU34480

Procedure for tilting down (hydro tilt
models)

1.

Release the tilt lock lever.

2.

Hold the rear of the top cowling with one
hand, tilt the outboard motor up slightly
and pull out the tilt support knob or return
the tilt support lever.

3.

Slowly tilt the outboard motor down.

4.

Place the tilt lock lever in the lock posi-
tion.

EMU33121

Procedure for tilting down (power trim
and tilt models)

1.

Push the power trim and tilt switch “

”

(up) until the outboard motor is supported
by the tilt rod and the tilt support lever be-
comes free.

2.

Release the tilt support lever.

3.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to the
desired position.

DN

ZMU01936

UP

DN

U6D779E0.book Page 62 Tuesday, November 15, 2011 2:33 PM

«
...
66
67
68
69
70
...
»

Содержание F80B





































































































Отзывы:

Нет отзывов

Похожие инструкции для F80B

Z690 Phantom Gaming 4

Бренд: ASROCK Страницы: 109

Бренд: Biostar Страницы: 85

Бренд: DFI Страницы: 8

Бренд: Beagleboard.org Страницы: 2

Бренд: TYAN Страницы: 90

Бренд: Commell Страницы: 61

Бренд: Intel Страницы: 43

Бренд: Shuttle Страницы: 80

EVAL-IH-R5IPB-A-V1

Бренд: Infineon Страницы: 34

Бренд: IBASE Technology Страницы: 62

Бренд: Microchip Technology Страницы: 54

Бренд: ECS Страницы: 87

LPC1768-MINI-DK2

Бренд: Haoyu Electronics Страницы: 4

G31M-GS R2.0-QVL

Бренд: ASROCK Страницы: 2

Бренд: Texas Instruments Страницы: 17

Бренд: DFI-ITOX Страницы: 121

Бренд: Ronetix Страницы: 11

Бренд: ASROCK Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды