Yamaha F25G Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 108

background image

Maintenance

80

quickly.

To prevent spilling oil where it could cause
damage to nature, it is strongly recommend-
ed that you use an oil changer to change the
engine oil. If an oil changer is not available,
drain the engine oil by removing the drain
screw. If you are not familiar with the proce-
dure for changing the engine oil, consult your
Yamaha dealer.
(1) Put the outboard motor in an upright po-

sition (not tilted).

NOTICE:

If the out-

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

[ECM01862]

(2) Start the engine. Warm it up and keep

the idle speed for 5-10 minutes.

(3) Stop the engine and leave it for 5-10

minutes.

(4) Remove the top cowling.
(5) Remove the oil filler cap. Pull out the dip-

stick and use the oil changer to extract
the oil completely.

TIP:

When using an oil changer, skip steps 6 and
7.
(6) Prepare a suitable container that holds a

larger amount than the engine oil capac-

ZMU03659

1. Oil filler cap

1. Oil dipstick

1. Oil changer

1

ZMU08799

1

ZMU0

8

751

1

ZMU08797

6FM-28199-75-1E0.book 80 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

«
...
84
85
86
87
88
...
»

Содержание F25G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F25G

KT333 DRAGON Plus

Бренд: SOYO Страницы: 34

Бренд: Sail Страницы: 18

Бренд: JETWAY Страницы: 48

TPS53355EVM-864

Бренд: Texas Instruments Страницы: 29

PP-I7RS400 PURE PERFORMANCE II

Бренд: Sapphire Audio Страницы: 44

Бренд: Telit Wireless Solutions Страницы: 47

Бренд: Infineon Страницы: 11

Бренд: IDT Страницы: 18

Бренд: Wemos Страницы: 12

Бренд: DFI Страницы: 96

Бренд: Lenovo Страницы: 51

cPCI-6620 Series

Бренд: ADLINK Technology Страницы: 80

Бренд: Ronetix Страницы: 11

Бренд: Freetech Страницы: 56

Бренд: Freescale Semiconductor Страницы: 38

Бренд: Freescale Semiconductor Страницы: 54

Бренд: Freescale Semiconductor Страницы: 50

Бренд: Create Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды