Yamaha F25G Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 108

background image

Specifications and requirements

16

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an
alternative oil grade listed under Recom-
mended engine oil grade 2.

Recommended engine oil grade 1

Recommended engine oil grade 2

EMU36361

Fuel requirements

EMU40203

Gasoline

Use a good quality gasoline that meets the
minimum octane rating. If knocking or ping-
ing occurs, use a different brand of gasoline
or premium unleaded fuel.

ECM01982



Do not use leaded gasoline. Leaded
gasoline can seriously damage the en-
gine.



Avoid getting water and contaminants
in the fuel tank. Contaminated fuel can
cause poor performance or engine
damage. Use only fresh gasoline that
has been stored in clean containers.

TIP:



This mark identifies the recommended fuel
for this outboard motor as specified by Eu-
ropean regulation (EN228).



Check that gasoline nozzle has the same
identifier when fueling.

Recommended engine oil:

YAMALUBE 4 or 4-stroke outboard

motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30

API SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50

API SH/SJ/SL

Engine oil quantity (without oil filter

replacement):

1.0 L (1.0 US qt, 0.85 Imp.qt)

Engine oil quantity (with oil filter re-

placement):

1.1 L (1.2 US qt, 1.0 Imp.qt)

ZMU06854

122˚F

50˚C

104

40

86

30

68

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

ZMU06855

122˚F

50˚C

104

40

86

30

68

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

Recommended fuel:

Regular unleaded gasoline

Min. research octane number (RON):

90

E5

E10

6FM-28199-75-1E0.book 16 ページ２０１９年１２月３日　火曜日　午後１時４３分

«
...
20
21
22
23
24
...
»

Содержание F25G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F25G

Бренд: Xilinx Страницы: 23

Бренд: Xilinx Страницы: 60

Бренд: Xilinx Страницы: 41

Zynq UltraScale+ ZCU104

Бренд: Xilinx Страницы: 92

Zynq UltraScale+ ZCU104

Бренд: Xilinx Страницы: 4

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 10

Бренд: Xilinx Страницы: 92

Бренд: Acconeer Страницы: 14

Бренд: Navia Страницы: 26

Airborne WLNN-EK-DP55x

Бренд: B&B Electronics Страницы: 6

Avnet Ultra96-PYNQ

Бренд: Xilinx Страницы: 19

Бренд: Microchip Technology Страницы: 31

Бренд: Aaeon Страницы: 111

Бренд: Memec Страницы: 45

Бренд: ICP Страницы: 50

Бренд: BESTEK Страницы: 13

Бренд: Linear Technology Страницы: 6

Бренд: Liantec Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды