Yamaha F150A2 Скачать руководство пользователя страница 72

Страница: 72 / 108

Operation

EMU42702

Procedure for tilting down

Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

Release the tilt support lever.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

EMU28063

Shallow water

EMU32852

Power trim and tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

NOTICE

ECM00261

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

EMU32923

Procedure for power trim and tilt models

Place the remote control lever in neutral.

ZMU01936

ZMU04603

U63P3FE0.book Page 66 Thursday, December 5, 2013 10:01 AM

2019 Yamaha Motor Corporation, U.S.A.

Содержание F150A2













































































































Результаты поиска

Содержание F150A2

Отзывы:

Бренды по названию

Популярные бренды

Yamaha F150A2, Руководство пользователя

Результаты поиска

Содержание F150A2

Отзывы:

Бренды по названию

Популярные бренды