Yamaha EMX 68S Скачать руководство пользователя

Страница: 8 / 34

EMX88S/EMX68S Quick Guide

EMX88S/EMX68S—Owner’s Manual

EMX88S/EMX68S
Quick Guide

The following steps (1–5) explain the basic con-
nection and operation of the EMX88S/EMX68S.

Also, please read “Front and Rear Panel” and
“Basic Operation” following this Quick Guide
section to learn more about using the EMX88S/
EMX68S.

Connection

Connecting speakers

Using speaker cables, connect each speaker to the
SPEAKERS A 1 jack and to the B 1 jack in the
SPEAKERS jack section on the rear panel of the
EMX88S/EMX68S.

• The diagram above shows an example of connecting

two main speakers. Refer to pages 17–18 for other
connection examples.

• You may connect to either of the two jacks on the

speakers.

• Be sure to use a cable designed for speaker connec-

tion.

Never connect the speakers in the manner shown
below. Otherwise, the EMX88S/EMX68S’s built-
in power amplifier will be damaged.

Setting the power amplifier mode

Set the power amp select switch (located on the
right corner on the panel) to MAIN L-R.

• This Quick Guide assumes that two main speakers

are connected. Refer to pages 13, 17, 18 for other
connections and power amp select switch settings.

• When the power amp select switch is set to the

MAIN L-R position, the stereo L signal will be out-
put from the SPEAKERS A jacks, and the stereo R
signal will be output from the SPEAKERS B jacks.

STEP 1

EMX88S (EMX68S)

Power amp select switch

Содержание EMX 68S



































Результаты поиска

Содержание EMX 68S

Отзывы:

Похожие инструкции для EMX 68S

Бренды по названию

Популярные бренды

Yamaha EMX 68S, Руководство пользователя

Результаты поиска

Содержание EMX 68S

Отзывы:

Похожие инструкции для EMX 68S

Бренды по названию

Популярные бренды