Yamaha EF7000 Скачать руководство пользователя

Страница: 28 / 178

2-7

CHK

ADJ

PERIODIC MAINTENANCE

AIR FILTER ELEMENT

NOTICE

Be sure not to run the engine without air
filter element. Otherwise this can result in
excessive piston and/or cylinder wear.

1. Remove:

Air filter cover screws

Air filter cover

2. Remove:

Air filter element

3. Check:

Air filter element

Damage

→

Replace.

Clogged

→

Wash the element with sol-

vent, and then dry it thoroughly.

Oil the element and squeeze out the

excess oil.

WARNING

Do not wash the element with gasoline or
with acidic, alkalic, or organic solvents.

NOTICE

Do not wring out the element. This could
cause it to tear.

4. Install:

Air filter element

Air filter cover

Air filter cover screws

1.6 Nm (0.16 m · kgf, 1.2 ft · lbf)

Содержание EF7000



















































































































































































Результаты поиска

Содержание EF7000

Отзывы:

Похожие инструкции для EF7000

Бренды по названию

Популярные бренды

Yamaha EF7000, Руководство по обслуживанию

Результаты поиска

Содержание EF7000

Отзывы:

Похожие инструкции для EF7000

Бренды по названию

Популярные бренды