Yamaha DX150B Скачать руководство пользователя страница 42

Страница: 42 / 124

2-19

701054

213022

EMU00172

OIL LEVEL WARNING / OIL FILTER
CLOGGING WARNING

This engine has an oil level warning sys-
tem. If oil level falls below lower limit, the
warning device will activate.

(

); Included (—); N/A

If the warning system has been activated,
stop the engine and check for the cause.

NOTE:

The warning for oil filter clogging is simi-
lar to the warnings for low oil level and
overheating. For easy troubleshooting, it
is advisable to check for engine overheat-
ing first, then oil level and finally oil filter
clogging.

Oil filter

Warning device

Tiller

Remote

activation

control

model

The engine speed
will automatically

decrease to about
2,000 r/min.

The oil level warning

indicator will come on.

The buzzer will sound.

905012

001054

67N-9-14-2 2/28/02 10:13 AM Page 20

Содержание DX150B





























































































































Результаты поиска

Содержание DX150B

Отзывы:

Похожие инструкции для DX150B

Бренды по названию

Популярные бренды

Yamaha DX150B, Руководство пользователя

Результаты поиска

Содержание DX150B

Отзывы:

Похожие инструкции для DX150B

Бренды по названию

Популярные бренды