Yamaha DX150B Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 124

background image

E

2-14

EMU01277

Fuel Economy

This meter displays the distance per liter
or gallon when cruising for reference use
by the operator.
Repeatedly push and release the “mode”
button until the indicator on the face of
the meter points to “ECON.”

NOTE:

If twin engines are installed on your boat,
the meter will display only the total fuel
economy of both engines.

P S

mpg

Km/L

gph

I/h

ECON SYNC

TTL

FUEL MANAGEMENT

P S

mp

Km

gph

I/h

ECON SYNC

TTL

FUEL MANAGEMENT

/L

g

EMU01276

Fuel Consumption Meter

This  meter  displays  the  total  amount  of
fuel  consumed  since  the  meter  was  last
reset.
Repeatedly push and release the “mode”
button  until  the  indicator  on  the  face  of
the meter points to total (“TTL”). To reset
the  total  fuel  consumption  to  “0”,  press
the “set” and “mode” buttons together.

67N-9-14-2 2/28/02 10:13 AM Page 15

«
...
35
36
37
38
39
...
»

Содержание DX150B





























































































































Отзывы:

Нет отзывов

Похожие инструкции для DX150B

Бренд: Intel Страницы: 80

Бренд: Microchip Technology Страницы: 17

Бренд: DFI Страницы: 8

Бренд: Quick Страницы: 32

Бренд: JETWAY Страницы: 38

MBATX-845GV-VEAH

Бренд: Kontron Страницы: 70

Бренд: ASROCK Страницы: 27

Бренд: JETWAY Страницы: 37

PENTIUM PRO W6-LI

Бренд: Micronics Страницы: 82

Бренд: ASROCK Страницы: 226

Бренд: JETWAY Страницы: 40

Бренд: Gigabyte Страницы: 40

Бренд: Aaeon Страницы: 56

Бренд: SOYO Страницы: 94

GA-Z97X-Gaming G1

Бренд: Gigabyte Страницы: 136

Бренд: Supermicro Страницы: 1

Бренд: Texas Instruments Страницы: 22

Бренд: bolid Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды