Yamaha DVR-S60, Руководство по обслуживанию

Страница: 55 / 108

DVR-S60/NX-SW60
55
DVR-S60
NX-SW60
IC806,807 EM636165TS,KM416S1120DT,K4S161622D (1 Mega x 16 Synchronous DRAM)
1 2 3 4 5 6 7 8 9
10 11 12 13 14
50 49 48 47 46 45 44 43 42 41 40 39 38 37
V
SS
DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ85 N.C/RFU
V
DD
DQ0 DQ1
V
SSQ
DQ2 DQ3
V
DDQ
DQ4 DQ5
V
SSQ
DQ6 DQ7
V
DDQ
LDQM
15 16 17 18 19 20 21 22 23 24 25
36 35 34 33 32 31 30 29 28 27 26
UDQM CLK CKE N.C A9 A8 A7 A6 A5 A4 V
SS
V
SSQ
V
SSQ
V
DDQ
V
DDQ
WE
CAS RAS
CS
BA
A10/AP
A0 A1 A2 A3
V
DD
Pin Name Input Function
CLK System Clock Active on the positive going edge to sample all inputs.
CS Chip Select
Disables or enable device operation by masking or enabling all inputs except
CLK,CKE and L(U)DQM
CKE Clock Enable
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least ono cycle prior to new command.
Disable input buffers for power down in standby.
A0~A10/AP Address
Row / column addresses are multiplexed on the same pins.
Row address : RA0~RA10, column address : CA0~CA7
BA Bank Select Address
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
RAS
Row Address Strobe
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
CAS Column Address Strobe
Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
WE Write Enable
Enables write operation and row precharge.
Latches data in standing from CAS, WE active.
L(U)DQM Data Input/Output Mask
Makes data output Hi-Z, t
SHZ
after the clock and masks the output.
Blocks data input when L(U)DQM active.
DQ0~15 Data Input/Output Data inputs/outputs are multiplexed on the same pins.
V
DD
/V
SS
Power Supply/Ground Power and ground for the input buffers and the core logic.
V
DDQ
/V
SSQ
Data Output Power/Ground
Isolated power supply and ground for the output buffers to provide improved noise
immunity.
N.C/RFU
No Connection/
Reserved for Future Use
This pin is recommended to be left No Connection on the device.
IC811 PQ025EZ01ZPN (Low Voltage Operation Low
Power-Loss VoltageRegulators)
1 3
2
5
1 2 3 4 5
Specific IC
1 DC input (V
IN
)
2 ON/OFF control terminal (V
C
)
3 DC output (V
O
)
4 NC
5 GND
IC812 PST3627UR (Reset IC)
OUT
GND
V
DD
C
D
2
1
GND 1
V
DD
OUT
C
D
2
4
3
3
4
R
D
Vref
PIN No.
1
2
3
4
PIN NAME
GND
V
DD
C
D
OUT
FUNCTIONS
GND Pin
V
DD
Pin / Voltage Detect Pin
Capacitor Connect Pin with Delay
Reset Signal Output Pin
MPEG P.C.B.