background image

5

SPEAKER SETUP

SPEAKERS TO BE USED

This unit is designed to provide the best sound-field quality with a 5 speaker configuration.  The most effective speakers to use with
this unit are front speakers, rear speakers and a center speaker.  You may omit the center speaker.  (Refer to the “4-Speaker
Configuration
” shown below.)
The front speakers are used for the main source sound plus the effect sounds.  They will probably be the speakers from your
present stereo system.  The rear speakers are used for the effect and surround sounds, and the center speaker is for the center
sounds (dialog etc.) within the Dolby Surround encoded programs.  The center speaker needs to be equal in power to the front
speakers, although the rear speakers should not be equal.  However, all the speakers should have high enough power handling to
accept the maximum output of this unit.

SPEAKER CONFIGURATION

5-Speaker Configuration

This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers.  If the digital sound field program DOLBY
PRO LOGIC 
or DOLBY PRO LOGIC ENHANCED is selected,
conversations will be output from the center speaker and the
ambience will be excellent.

Set the center channel mode to the “NORMAL” or “WIDE
position.  (For details, refer to page 10.)

4-Speaker Configuration

The center speaker is not used in this configuration.  If the
digital sound field program DOLBY PRO LOGIC or DOLBY
PRO LOGIC ENHANCED 
is selected, the center sound is
output from the left and the right front speakers.  However, the
sound effect of other programs can be the same as that of the
5-speaker configuration.

Be sure to set the center channel mode to the “PHANTOM
position.  (For details, refer to page 10.)

SPEAKER PLACEMENT

The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs:  front speakers (your normal
stereo speakers), and rear speakers, plus a center speaker.   When you place these speakers, refer to the following.

Front:

In normal position.  (The position of your present
stereo speaker system.)

Rear:

Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.

Center: Precisely between the front speakers.  (To avoid

interference with TV sets, use a magnetically shielded
speaker.)

Front L

Center

Front R

Dialogue

Surround sound

Dialogue

Surround sound

Rear L

Rear R

Front L

Front R

Dialogue

Surround sound

Dialogue

Surround sound

Rear L

Rear R

Front R

Center

Front L

TV set

Rear R

Rear L

Содержание DSP-E390

















Отзывы: