Yamaha DSP-A595a страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 60

background image

18

Connecting the AM loop antenna

• The AM loop antenna should be placed away from this unit. The antenna may be hung on a wall.
• The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

1

2

3

ANTENNA CONNECTIONS

Each antenna should be correctly connected to the designated terminals, referring to the following diagram.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor
reception quality, an outdoor antenna may result in improvement.

GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground
is a metal stake driven into moist earth.

2

Attach the loop antenna to the
antenna stand.

Outdoor

FM antenna

75-ohm/300-ohm
antenna adapter

75-ohm coaxial cable

75-ohm/300-ohm
antenna adapter

300-ohm feeder

Ground

AM loop
antenna
(included)

Outdoor AM antenna

* If you cannot obtain good

reception with the AM loop
antenna, connect 5 m to
10 m of vinyl covered wire
to the AM ANT terminal
and extend it outdoors
from a window. (Be sure
to also connect the AM
loop antenna at this time.)

Indoor FM antenna
(included)

* Firmly insert the

connector into the FM
ANT terminal.

Loop antenna

Antenna stand

* You may be unable to obtain good FM radio

reception depending on your local
conditions (distance from the broadcast
station, interposing buildings and
mountains, etc.). Consult your dealer or
authorized service center and be sure to
install an antenna that suits your local
conditions.
Install the special FM outdoor antenna in a
high place as far away from any roads as
possible to avoid being affected by
automobile ignition noise.

1

1

Press the tab and unlock the terminal hole.

2

Connect the AM loop antenna lead wires to the
AM ANT and GND terminals.

3

Return the tab to its original position to lock the
lead wires. Lightly pull the lead wires to confirm
a good connection.

3

Orient the AM loop
antenna so that the best
reception is obtained.

01RX-V595aRDS-2

6/24/99, 10:59 AM

18

«
...
16
17
18
19
20
...
»

Содержание DSP-A595a





























































Отзывы:

Нет отзывов

Похожие инструкции для DSP-A595a

Бренд: Hamilton/Buhl Страницы: 16

Бренд: Hamilton Electronics Страницы: 5

PowerLight Series

Бренд: QSC Страницы: 100

Бренд: Yamaha Страницы: 84

Go Wireless Series

Бренд: Vernier Страницы: 3

Бренд: OM POWER Страницы: 56

Бренд: Linear Technology Страницы: 9

Бренд: Optimus Страницы: 14

Бренд: PA Tech Страницы: 5

Бренд: Nobsound Страницы: 2

Бренд: DaytonAudio Страницы: 4

Бренд: Technalogix Страницы: 55

Бренд: Unika Страницы: 16

Бренд: Bugera Страницы: 15

Бренд: Teac Страницы: 48

Бренд: Saluki Страницы: 85

Бренд: ALLNIC AUDIO Страницы: 6

Бренд: L.R. Baggs Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды