background image

 

 

2

 
Overview .......................................................................................................................... 3 
Functionality enabled by connecting the DM1000 V2 to your video editor .................... 3 
1.  Make settings in your video editor ............................................................................ 4 
2.  Connect the DM1000 V2 to your video editor .......................................................... 4 
3.  Connect the DM1000 V2 to your video recorders .................................................... 5 
4.  Enable commands to be exchanged with the video editor ........................................ 6 
5.  Verify that the DM1000 is correctly connected to your video editor ........................ 7 
6.  Match the frame type with the video......................................................................... 8 
7.  Initialize the DM1000’s mixer settings ..................................................................... 9 
8.  Patch the INPUT jack signals to input channels........................................................ 9 
9.  Patch the bus signals to output jacks ....................................................................... 10 
10. 

Assign the audio channel inputs for the video recorders and the DM1000 ......... 10 

11. 

Specify the fader operation of the DM1000......................................................... 12 

12. 

Specify the output destination (bus) for the signals input to the DM1000 .......... 13 

12.1  If you are not using pre-read ................................................................................ 13 
12.2  If you are using pre-read ...................................................................................... 14 
13. 

Set the panning of the signals being input to the DM1000.................................. 14 

14. 

Pair the input channels ......................................................................................... 15 

15. 

Use the panel [SEL] LED to indicate the ESAM fader on/off status................... 16 

16. 

Adjust the input/output levels .............................................................................. 16 

17. 

Specify the delay for the input channels .............................................................. 17 

18. 

Store the scene memory ....................................................................................... 17 

19. 

Controlling the system from your video editor.................................................... 17 

 

 

Содержание DM 1000



















Отзывы: