Yamaha Diver 510N F XJ6F страница 72 Скачать руководство пользователя

Страница: 72 / 102

PERIODIC MAINTENANCE AND ADJUSTMENT

6-27

3. Tighten the axle nut, and then

tighten the locknuts to the speci-
fied torques.

EAU23025

Cleaning and lubricating the
drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

NOTICE

ECA10583

The drive chain must be lubricated
after washing the motorcycle, riding
in the rain or riding in wet areas.

1. Clean the drive chain with kero-

sene and a small soft brush.

NOTICE:

To prevent damaging

the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents.

[ECA11121]

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

NOTICE:

Do not use

engine oil or any other lubri-
cants for the drive chain, as they

may contain substances that
could damage the O-rings.

[ECA11111]

1. Alignment plate
2. Notch

Tightening torques:

Axle nut:

90 Nm (9.0 m·kgf, 65 ft·lbf)

Locknut:

16 Nm (1.6 m·kgf, 11 ft·lbf)

U1CWE0E0.book Page 27 Friday, September 11, 2009 9:05 AM

Содержание Diver 510N F XJ6F







































































































Результаты поиска

Содержание Diver 510N F XJ6F

Отзывы:

Похожие инструкции для Diver 510N F XJ6F

Бренды по названию

Популярные бренды

Yamaha Diver 510N F XJ6F, Руководство пользователя

Результаты поиска

Содержание Diver 510N F XJ6F

Отзывы:

Похожие инструкции для Diver 510N F XJ6F

Бренды по названию

Популярные бренды