Yamaha Diver 510N F XJ6F страница 85 Скачать руководство пользователя

Страница: 85 / 102

PERIODIC MAINTENANCE AND ADJUSTMENT

6-40

EAU44800

Rear wheel (XJ6F)

WARNING

EWA14840

For the ABS model, have a Yamaha
dealer remove and install the wheel.

EAU32874

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the locknut and drive chain

slack adjusting nut on each side of
the swingarm.

2. Loosen the axle nut.

3. Place the motorcycle on the cen-

terstand.

4. Remove the axle nut.
5. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

TIP

The drive chain does not need to be
disassembled in order to remove and
install the rear wheel.

6. While supporting the brake caliper

and slightly lifting the wheel, pull
the wheel axle out.

TIP

A rubber mallet may be useful to tap the
wheel axle out.

1. Axle nut
2. Drive chain slack adjusting nut

3. Locknut

1. Locknut

2. Drive chain slack adjusting nut
3. Brake caliper bracket

4. Brake caliper

5. Wheel axle

U1CWE0E0.book Page 40 Friday, September 11, 2009 9:05 AM

Содержание Diver 510N F XJ6F







































































































Результаты поиска

Содержание Diver 510N F XJ6F

Отзывы:

Похожие инструкции для Diver 510N F XJ6F

Бренды по названию

Популярные бренды

Yamaha Diver 510N F XJ6F, Руководство пользователя

Результаты поиска

Содержание Diver 510N F XJ6F

Отзывы:

Похожие инструкции для Diver 510N F XJ6F

Бренды по названию

Популярные бренды