Yamaha Diver 510N F XJ6F страница 67 Скачать руководство пользователя | Manualshive

Страница: 67 / 102

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

6-22

6

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU47390

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the clutch lever free play adjusting
bolt at the clutch lever in direction (a).
To decrease the clutch lever free play,
turn the adjusting bolt in direction (b).

TIP

If the specified clutch lever free play
cannot be obtained as described
above, proceed as follows.

1. Fully turn the adjusting bolt at the

clutch lever in direction (a) to loos-
en the clutch cable.

2. Remove cowlings A and B. (See

page 6-7.)

3. Loosen the locknut further down

the clutch cable.

4. To increase the clutch lever free

play, turn the clutch lever free play
adjusting nut in direction (a). To
decrease the clutch lever free play,
turn the adjusting nut in direction
(b).

1. Clutch lever free play adjusting bolt

2. Clutch lever free play

U1CWE0E0.book Page 22 Friday, September 11, 2009 9:05 AM

«
...
65
66
67
68
69
...
»

Содержание Diver 510N F XJ6F







































































































Отзывы:

Нет отзывов

Похожие инструкции для Diver 510N F XJ6F

Бренд: probrake Страницы: 2

Бренд: Happy Trails Страницы: 4

Бренд: Dakota Digital Страницы: 7

Бренд: METRAKIT Страницы: 53

Бренд: R&G Страницы: 8

DaVinci RSV4-APRC

Бренд: STARLANE Страницы: 2

Бренд: Cake Страницы: 12

Daytona 955i 2002

Бренд: Triumph Страницы: 384

Бренд: AFX Страницы: 112

Multistrada 620

Бренд: Ducati Страницы: 382

TRACER MTT9K 2019

Бренд: Yamaha Страницы: 122

TT-R125(N) 2000

Бренд: Yamaha Страницы: 508

TT-R125(R) 2002

Бренд: Yamaha Страницы: 510

Бренд: Yamaha Страницы: 610

TT-R125(S) 2003

Бренд: Yamaha Страницы: 610

Бренд: Yamaha Страницы: 616

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды