background image

30

Operation

EMU36381

First-time operation

EMU27020

Breaking in engine

Your new engine requires a period of break-
in to allow mating surfaces of moving parts to
wear in evenly. Correct break-in will help en-
sure proper performance and longer engine
life.

NOTICE

ECM00140

Failure to follow the break-in procedure
could result in reduced engine life or
even severe engine damage.

Premix fuel must be used during break-
in in addition to oil in the oil injection
system.

EMU27060

Gasoline and engine oil mixing chart
(50:1)

NOTICE

ECM00150

Be sure to mix gasoline and oil complete-
ly, otherwise the engine may be dam-
aged.

EMU30311

Procedure for oil injection models

Run the engine under load (in gear with a
propeller installed) for 10 hours as follows.
1. First 10 minutes:

Run the engine at the lowest possible

speed. A fast idle in neutral is best.

2. Next 50 minutes:

Do not exceed half throttle (approxi-
mately 3000 r/min). Vary engine speed
occasionally. If you have an easy-plan-
ing boat, accelerate at full throttle onto
plane, then immediately reduce the
throttle to 3000 r/min or less.

3. Next two hours:

Accelerate at full throttle onto plane,
then reduce engine speed to three-quar-
ter throttle (approximately 4000 r/min).
Vary engine speed occasionally. Run at
full throttle for one minute, then allow
about 10 minutes of operation at three-
quarter throttle or less to let the engine
cool.

4. Remaining seven hours:

Run the engine at any speed. However,
avoid operating at full throttle for more
than 5 minutes at a time.

5. After the first 10 hours:

Operate the engine normally. Use only
straight gasoline in the fuel tank. The
Yamaha oil injection system provides
proper lubrication for normal operation.

EMU36400

Getting to know your boat

Different boats handle differently. Operate
cautiously while you learn how your boat
handles under different conditions and with
different trim angles (see page 44).

EMU36413

Checks before starting engine

WARNING

EWM01921

If any item in “Checks before starting en-
gine” is not working properly, have it in-
spected and repaired before operating
the outboard motor. Otherwise, an acci-
dent could occur.

1.

: Gasoline

2.

: Engine oil

6H1-9-2A-1E0.book  30 ページ  2010年2月17日 水曜日 午前10時42分

Содержание 90A



















































































Отзывы: