Yamaha 60 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 82

Yamaha 60 Скачать руководство пользователя страница 34

Operation

29

tank cap, loosen it 2 or 3 turns.

2.

If there is a fuel joint on the motor, firmly
connect the fuel line to the joint. Then
firmly connect the other end of the fuel
line to the joint on the fuel tank.

3.

If a steering friction adjuster is provided
on your outboard motor, securely attach
the fuel line to the fuel line clamp.

NOTE:

During engine operation place the tank hori-

zontally, otherwise fuel cannot be drawn

from the fuel tank.

4.

Squeeze the primer pump with the outlet
end up until you feel it become firm.

EMU27490

Starting engine

EMU27592

Electric start / prime start models

1.

Place the gear shift lever in neutral.

NOTE:

The start-in-gear protection device prevents
the engine from starting except when in neu-

tral.

2.

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then install the lock plate on
the other end of the lanyard into the en-

ZMU02295

ZMU03833

ZMU02024

ZMU02025

«
...
32
33
34
35
36
...
»

Содержание 60



















































































Отзывы:

Нет отзывов