Yamaha 60 Скачать руководство пользователя страница 23

Страница: 23 / 82

Basic components

EMU26470

Tachometer

This gauge shows the engine speed and has
the following functions.

EMU26491

Digital tachometer

The tachometer shows the engine speed
and has the following functions.

NOTE:

All segments of the display will light momen-
tarily after the main switch is turned on and

will return to normal thereafter.

NOTE:

The water separator and engine trouble
warning indicators only operate when the en-
gine is equipped with the appropriate func-

tions.

EMU26540

Oil level indicators (three indicators
2)

The indicators on the gauge show the status
of the oil level. For details on how to read the
indicators, see page 28.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26550

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. For fur-
ther information, see page 21.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

1. Tachometer
2. Oil level indicator

1. Tachometer
2. Trim meter
3. Hour meter
4. Oil level indicator
5. Overheat warning indicator
6. Water separator warning indicator

ZMU04577

ZMU01958

7. Engine trouble warning indicator
8. Set button
9. Mode button

1. Oil level indicators

ZMU04580

Содержание 60



















































































Результаты поиска

Содержание 60

Отзывы:

Yamaha 60, Руководство пользователя, Страница: 23 / 82

Результаты поиска

Содержание 60

Отзывы: