Yamaha 60 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 82

Yamaha 60 Скачать руководство пользователя страница 33

Operation

28

EMU27321

Oil level indicator operation

The various functions of the oil level system are as follows:

EMU27360

Electric start models

EMU27450

Operating engine

EMU27461

Feeding fuel (portable tank)

WARNING

EWM00420

●

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the
water near you.

●

When the air vent screw is loosened,
gasoline vapor will be released. Gaso-
line is highly flammable, and its vapors

are flammable and explosive. Refrain
from smoking, and keep away from
open flames and sparks while loosen-
ing the air vent screw.

●

This product emits exhaust gases
which contain carbon monoxide, a col-
orless, odorless gas which could cause
brain damage or death when inhaled.
Symptoms include nausea, dizziness,
and drowsiness. Keep cockpit and cab-
in areas well ventilated. Avoid blocking

exhaust outlets.

1.

If there is an air vent screw on the fuel

Oil level
warning

indicator

(digital

tachometer)

Oil level
warning

indicator

(analog

tachometer/

bottom

cowling)

Engine oil tank

Remarks

Green

more than 770

cm

3

(0.81 US qt,

0.68 Imp qt)

No refilling necessary.

Yellow

from 770 cm

3

(0.48 US qt, 0.40
Imp qt) down to

280 cm

3

(0.30 US

qt, 0.25 Imp qt)

Add oil; see page 27.

Red

280 cm

3

(0.30 US

qt, 0.25 Imp qt) or
less

●

Buzzer sounds in
remote control box
and engine speed is
limited to about 2000
r/min to help con-
serve oil.

●

Check oil filter for
clogging.

«
...
31
32
33
34
35
...
»

Содержание 60



















































































Отзывы:

Нет отзывов