Yamaha 5C Скачать руководство пользователя

Страница: 55 / 66

Maintenance

●

Check the propeller shaft oil seal for dam-
age.

EMU30662

Removing propeller

EMU29197

Spline models

Straighten the cotter pin and pull it out us-
ing a pair of pliers.

Remove the propeller nut, washer, and
spacer (if equipped).

WARNING! Do not

use your hand to hold the propeller
when loosening the propeller nut.

[EWM01890]

Remove the propeller, washer (if
equipped), and thrust washer.

EMU30672

Installing propeller

EMU30372

Spline models

NOTICE

ECM00500

Be sure to use a new cotter pin and bend
the ends over securely. Otherwise the pro-
peller could come off during operation and
be lost.

Apply Yamaha marine grease or a corro-
sion resistant grease to the propeller
shaft.

Install the spacer (if equipped), thrust
washer, and propeller on the propeller
shaft.

NOTICE:

Be sure to install the

thrust washer before installing the
propeller, otherwise the lower case
and propeller boss could be damaged.

[ECM01880]

Install the spacer (if equipped) and the
washer. Tighten the propeller nut until
there is no forward-and-backward move-
ment.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NOTICE:

Do not reuse the cotter pin

installed. Otherwise the propeller can
come off during operation.

[ECM01890]

1. Cotter pin

2. Propeller nut
3. Washer

4. Propeller

5. Thrust washer

U6E028E0.book Page 50 Tuesday, February 10, 2009 3:19 PM

Содержание 5C



































































Результаты поиска

Содержание 5C

Отзывы:

Похожие инструкции для 5C

Бренды по названию

Популярные бренды

Yamaha 5C, Руководство пользователя

Результаты поиска

Содержание 5C

Отзывы:

Похожие инструкции для 5C

Бренды по названию

Популярные бренды