Yamaha 2011 WR250FA Скачать руководство пользователя страница 201

Страница: 201 / 316

5-68

KICK SHAFT AND SHIFT SHAFT

2. Install:

• Torsion spring "1"

To kick shaft "2".

Make sure the stopper "a" of the torsion spring
fits into the hole "b" on the kick shaft.

3. Install:

• Spring guide "1"

Slide the spring guide into the kick shaft, make
sure the groove "a" in the spring guide fits on
the stopper of the torsion spring.

4. Install:

• Kick shaft assembly "1"
• Washer "2"

• Apply the molybdenum disulfide grease on

the contacting surfaces of the kick shaft stop-
per "a" and kick shaft ratchet wheel guide "3".

• Apply the engine oil on the kick shaft.
• Slide the kick shaft assembly into the crank-

case and make sure the kick shaft stopper "a"
fits into the kick shaft ratchet wheel guide.

5. Hook:

• Torsion spring "1"

Turn the torsion spring clockwise and hook into
the proper hole "a" in the crankcase.

INSTALLING THE KICK IDLE GEAR

1. Install:

• Kick idle gear "1"
• Washer "2"
• Circlip "3"

• Apply the engine oil on the kick idle gear inner

circumference.

• Install the kick idle gear with its depressed

side "a" toward you.

Содержание 2011 WR250FA





























































































































































































































































































































Результаты поиска

Содержание 2011 WR250FA

Отзывы:

Похожие инструкции для 2011 WR250FA

Бренды по названию

Популярные бренды

Yamaha 2011 WR250FA, Руководство по эксплуатации для владельца

Результаты поиска

Содержание 2011 WR250FA

Отзывы:

Похожие инструкции для 2011 WR250FA

Бренды по названию

Популярные бренды