Yamaha 2010 WaveRunner VX Cruisel Скачать руководство пользователя | Manualshive

Страница: 71 / 106

background image

Operation

66

EJU40210

Riding position

Operator riding position

The operator should grip the handlebars firm-
ly with both hands and sit astride the seat with
both feet on the floor of the footwell.

Passenger riding position

The passenger(s) should hold on firmly, either
to the person in front of them or to the hand-
grip provided, and sit astride the seat with
their feet on the floor of the footwell. Never al-
low a passenger to ride in front of the opera-
tor. (See page 17 for information on the riding
position when pulling a water-skier.)

EJU32802

Launching the watercraft

When launching the watercraft, make sure
that there are no obstacles around you.
If the watercraft is launched from a trailer,
someone should make sure that waves do not
push the watercraft into the trailer.

EJU36345

Starting the engine on water

WARNING

EWJ01530

Do not apply throttle when anyone is at the
rear of the watercraft. Turn the engine off
or keep it at idle. Water and debris exiting
the jet thrust nozzle can cause severe inju-
ry.

To start the engine:
(1) VX Deluxe / VX Cruiser: If the lock mode

is selected for the Yamaha Security Sys-
tem setting, select the unlock mode. (See
page 31 for Yamaha Security System
setting procedures.)

(2) Move the watercraft to an area that is free

from weeds and debris, and has a water
depth of at least 60 cm (2 ft) from the bot-
tom of the watercraft.

NOTICE:

Never

run the engine in water that is less
than 60 cm (2 ft) deep from the bottom
of the watercraft, otherwise pebbles or
sand could be sucked into the jet in-
take, causing impeller damage and en-
gine overheating.

[ECJ00472]

(3) Attach the engine shut-off cord (lanyard)

to your left wrist, and then attach the clip
to the engine shut-off switch. (See page
32 for information on operating the en-
gine shut-off switch.)

WARNING! Check

that the engine shut-off cord (lanyard)

UF2N10E0.book Page 66 Tuesday, October 6, 2009 5:02 PM

«
...
69
70
71
72
73
...
»

Содержание 2010 WaveRunner VX Cruisel











































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 WaveRunner VX Cruisel

Бренд: Zodiac Страницы: 55

Бренд: ABSTRACT Страницы: 12

3 Seat Sun Slider

Бренд: KL Industries Страницы: 12

Бренд: Confluence Watersports Страницы: 7

Бренд: Kingfisher Страницы: 35

Бренд: Gumotex Страницы: 40

Бренд: BENETEAU Страницы: 24

MERRY FISHER 585

Бренд: Jeanneau Страницы: 62

Бренд: Feathercraft Страницы: 21

Sportster Series

Бренд: Malibu Boats Страницы: 76

Бренд: Cobalt Digital Inc Страницы: 136

Бренд: Lowell Страницы: 2

Бренд: VFTech Страницы: 32

Бренд: Plastimo Страницы: 320

Бренд: Leisure Страницы: 26

Бренд: Bestway Страницы: 5

Бренд: Bestway Страницы: 28

65052 HYDRO-FORCE KAYAKS VENTURA

Бренд: Bestway Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды