Yamaha 2010 WaveRunner VX Cruisel Скачать руководство пользователя | Manualshive

Страница: 58 / 106

background image

Operation and handling requirements

53

EJU40021

Draining the bilge water

NOTICE

ECJ01301

Do not run the engine at full throttle when
bilge water remains in the engine compart-
ment. The bilge water can splash into the
engine, which can result in severe dam-
age.

EJU40033

Draining the bilge water on land

To drain the bilge water on land:
(1) Loosen the stern drain plugs and remove

them.

(2) Raise the bow of the watercraft, such as

by placing the watercraft on a slope, to
drain the bilge water from the engine
compartment.

(3) After the bilge water has drained from the

stern drain plug holes, wipe up any re-

maining moisture in the engine compart-
ment with a dry cloth.

(4) Securely install the stern drain plugs by

tightening them until they stop.

NOTICE:

Before installing the stern drain plugs,
clean the drain plug threads to remove
any foreign materials, such as dirt or
sand. Otherwise, the stern drain plugs
could be damaged, allowing water to
enter the engine compartment. Make
sure that the stern drain plugs are
tightened securely before launching
the watercraft. Otherwise, water may
flood the engine compartment and
cause the watercraft to submerge.

[ECJ00361]

EJU40534

Draining the bilge water on water

A small quantity of bilge water will remain in
the engine compartment even after the bilge
water is drained on water. To completely drain
the bilge water, remove the watercraft from
the water and drain the bilge water on land.

Jet vacuum bilge draining system

While the watercraft is operating, bilge water
in the engine compartment is drawn in by the
vacuum that is generated in the jet pump and
discharged from the watercraft through the jet
thrust nozzle.
To drain the bilge water on water:
Operate the watercraft as straight as possible
and above planing speed for at least 2 min-
utes.

NOTICE:

Do not run the engine at full

throttle for at least 1 minute after the en-
gine has been restarted. Bilge water in the
engine compartment can splash into the

1

Stern drain plug

1

UF2N10E0.book Page 53 Tuesday, October 6, 2009 5:02 PM

«
...
56
57
58
59
60
...
»

Содержание 2010 WaveRunner VX Cruisel











































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 WaveRunner VX Cruisel

Бренд: J/Boats Страницы: 88

Бренд: CATANA Group Страницы: 142

Бренд: Yamaha Страницы: 113

Бренд: LITEBOAT Страницы: 28

Бренд: Paddle King Страницы: 23

Бренд: Blue Wave Boats Страницы: 1

Mirage Eclipse 10.5

Бренд: Hobie Страницы: 20

Бренд: J/Boats Страницы: 58

Бренд: BENETEAU Страницы: 138

Бренд: UIM Страницы: 17

WaveRunner XL800

Бренд: Yamaha Страницы: 126

Бренд: Sailfish Страницы: 68

Бренд: Cobalt Digital Inc Страницы: 64

WaveRunner VXS 2012

Бренд: Yamaha Страницы: 98

Бренд: Malibukayaks Страницы: 15

Бренд: World Cat Страницы: 93

SilverWave 2019

Бренд: Bluewave Страницы: 32

Бренд: Sea-doo Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды