Yamaha 2005 YZF-R1T Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 106

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-20

6

EAU33890

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the adjusting bolt at the clutch lever
in direction (a). To decrease the clutch
lever free play, turn the adjusting bolt in
direction (b).

NOTE:

If the specified clutch lever free play
cannot be obtained as described
above, proceed as follows.

1. Fully turn the adjusting bolt at the

clutch lever in direction (a) to loos-
en the clutch cable.

2. Loosen the locknut at the crank-

case.

3. To increase the clutch lever free

play, turn the adjusting nut in direc-
tion (a). To decrease the clutch le-
ver free play, turn the adjusting nut
in direction (b).

4. Tighten the locknut.

EAU22270

Adjusting the rear brake light
switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a). To
make the brake light come on later, turn
the adjusting nut in direction (b).

1. Clutch lever free play adjusting bolt

2. Clutch lever free play

1. Locknut

2. Clutch lever free play adjusting nut (crank-

case)

1. Rear brake light switch

2. Rear brake light switch adjusting nut

U5VY21E0.book Page 20 Friday, September 10, 2004 9:21 AM

«
...
67
68
69
70
71
...
»

Содержание 2005 YZF-R1T











































































































Отзывы:

Нет отзывов

Похожие инструкции для 2005 YZF-R1T

Бренд: Kabuto Страницы: 25

Бренд: Fantic Motor Страницы: 130

Бренд: Yamaha Страницы: 82

Бренд: Suzuki Страницы: 151

Бренд: J&M Страницы: 5

65175810022-00-40

Бренд: hepco & becker Страницы: 4

Бренд: W&W Cycles Страницы: 5

fire PANTLINER AJ6

Бренд: ALPENHEAT Страницы: 26

Бренд: zeeltronic Страницы: 10

LIX9U0003740299

Бренд: X-lite Страницы: 116

Бренд: Yamaha Страницы: 276

Бренд: ICON Vehicle Dynamics Страницы: 4

Бренд: SUOMY Страницы: 26

Бренд: Parkside Страницы: 24

Бренд: Parkside Страницы: 109

Бренд: APRILIA Страницы: 216

Бренд: Saddlemen Страницы: 2

Бренд: Baotian Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды